Cooper Menvier 100 Podręcznik Użytkownika Pobierz pdf (Strona 36)

Technical Specification Menvier40/100

Page 32

communicator fitted the requirement drops

to 30 hours.

This means that all the devices powered by

the backup battery, including the control

unit and at least one keypad, should

together draw no more in total than an

average of 570mA over a 30 hour standby

time. Note that for Security Grade 3 the

control unit must use a plug-by

communicator, which may have its own

power supply.

For Security Grade 2 the required battery

standby time is 12 hours. However, the

total average current available over 12

hours from the 17Ah battery is limited by

the power supply to 750mA. (The current is

limited to 750mA because when mains is

present the 1.5A power supply reserves

750mA to recharge batteries, leaving

750mA available to supply the system.)

The table below shows the current

consumption of the control unit and each

device that can be fitted to it.

CIE power

requirement:

120mA min.

200mA max

i-kp01 power

requirement:

30mA (normal/idle)

45mA (backlight low)

65mA (backlight

high)

Wired Expander

requirement

20mA max quiescent.

300mA in alarm if

sounder connected.

Radio Expander

requirement

40mA max quiescent

320mA in alarm if

sounder connected.

Battery charging

requirement:

750mA per battery

(recharge to 80%

within 24 hrs)

Plug-on

Communicator

power requirement:

i-sd02 or i-dig02:

20mA quiescent

50mA max

Plug-on

Communicator

power requirement

i-gsm02:

150mA quiescent

and max.

Plug-by

Communicator pins

require:

3mA each when

active.

10 FSL zones

20mA

5 CCL zones

30mA

12V Bus output

voltage range :

10±0.5V to 13.8V

12V Aux output

voltage range:

10±0.5V to 13.8V

12V Bell output

voltage range

10±0.5V to 13.8V

Max p-to-p ripple

voltage:

0.5V

Standby Battery:

12V, 17Ah sealed

lead acid (not

supplied).

„Low battery‟ fault

at:

< 12V

Aux power output

fault at:

< 9V

Deep discharge

protection at:

10±0.5V

Overvoltage

protection trigger

voltage

15.8±1.0V

Standby time:

See “Power

Availability” on page

8.

Electromagnetic

Compatibility

Immunity

Conforms to EN50130-4.

Emissions

Conforms to EN61000-6-3.

Outputs

Panel: O/P 1

Voltage free, single pole

relay contacts rated 24VDC

@ 1A.

Panel:

O/P 2 - 3

Open collector transistor,

+12VDC when inactive, 0V

when active. 500mA max.

Plug-by O/P

1-16

Open collector transistor

+12VDC when inactive, 0V

when active, 50mA max.

LS 1

(loudspeaker)

Min impedance 16 Ohm per

output, current

consumption = 280mA in

alarm.

Expander:

Outputs

Open collector transistor,

+12VDC when inactive, 0V

when active. 500mA max.

Note: The current is limited

by the amount available

from the power supply

driving the expander.

Sounder Volume Levels (at 1m)

i-kp01 (at max volume)

70dB

Expander sounders

70dB

Expander 16 Ohm loudspeaker

93dB

Fuses

The control unit has a replaceable T250mA

mains fuse.

Electrical Safety

Conforms to EN60950-1.

1 2 ... 31 32 33 34 35 36 37 38

Komentarze do niniejszej Instrukcji

Brak uwag