Cooper TS690 Instrukcja Instalacji Strona 15
- Strona / 60
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4. Connect “Remote Network” cables and
detection circuit cables to the appropriate
terminals, see Figure 10
5. Set the I/D selector jumper link to the required
position:
TS690
I/D Selector Circuit A Circuit B
Panel
Output
107085
209106
311127
413148
ENG/NULL N/A N/A N/A
TS690ID
I/D Selector Circuit A Circuit B
Panel
Output
131325
233346
335367
436388
ENG/NULL N/A N/A N/A
l
No two LECs or remote keypads should
have the same I/D.
l
DO NOT set the I/D selector to the “NULL”
position.
6. Finally clip the LEC cover onto the base being
careful not to trap any cables or to obstruct the
tamper switch.
Wiring Detection Circuits
All detection circuits may be wired as “End Of Line”
(EOL) or “Double Pole” (DP). Both methods can be
used on the same equipment.
Double Pole
The DP method requires the following:
l
The detector alarm and tamper contacts are
connected to the zone and tamper terminals
respectively.
l
The combined alarm and tamper loop
resistance must be less than 100 Ohms.
l
The maximum number of detection devices
allowed in a circuit is ten.
l
Normally open devices such as pressure pads
and exit terminator buttons are connected
between the zone and tamper terminals.
l
If the detection circuit is not used links can be
fitted across the zone and tamper loops or
programmed as Not Used.
End Of Line
The EOL method requires the following:
l
The detector alarm contacts must have a 4K7
shunt resistor fitted.
l
A 2K2 End of Line (EOL) resistor must be fitted at
the point in the circuit furthest from the control
panel.
l
Loop resistance with the EOL resistor shorted
must be less than 100 Ohms.
l
The maximum number of detection devices
allowed in a circuit is ten.
l
Normally open devices such as pressure pads
and exit terminator buttons are connected
across outer terminals
l
If the detection circuit is not used links can be
fitted across the zone and tamper loops or
programmed as Not Used.
15
TS690 & TS690ID Installation Manual System Installation
Alarm
Tamper
CIRCUIT A
ZA
TA
CIRCUIT A
ZA
TA
CIRCUIT A
ZA
TA
Alarm
Tamper
Max. 10 devices per circuit
Wiring N.O. devices (Exit Terminators)
Alarm
Tamper
500 metres or 100 Ohms
Figure 12. Double Pole Wiring
- TS690 & TS690ID 1
- Overview 2
- System Installation 2
- Engineer’s Menu 1 2
- Engineer's Menu 2 3
- Appendices 3
- Number of Zones = 8 to 14 5
- Number of Zones = 2 to 38 5
- Supply: 230V ±10% 50Hz 6
- ID Loop Wiring (TS690ID Only) 8
- Cabling Requirements 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- FUSE 315mA 12
- Installation Procedure 13
- Engineer’s Keypad 14
- TS700 LEC Installation 14
- Wiring Detection Circuits 15
- Double Pole 15
- End Of Line 15
- Wiring ID Biscuits 16
- Biscuit Connections 16
- Wiring A Biscuit to a PIR 16
- External Sounder Connections 17
- Auxiliary Tamper 17
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 18
- DC6 Digi-Modem Installation 18
- Regulatory Requirements 18
- Application 19
- Approval 19
- Connections 19
- Installation 20
- DC54 & DC58M Installation 20
- DATAC or RS232 printer 21
- CPA6 Printer 21
- RS232 Data 21
- Pre Power-Up Checks 22
- Initial Power-Up 23
- Power-Up Checks 23
- NVM Defaults 24
- Panel Outputs [1.1] 26
- Digicom Outputs [1.2] 26
- Digicom Channels [1.3] 26
- Programmable Output Types 26
- No Type/Description 27
- Program Circuits [1.4] 29
- Circuit Types 29
- Circuit Attributes 30
- System Timers [1.5] 31
- Setting Modes [1.6] 33
- Do System Print [1.7] 34
- Remote Reset Algorithm [1.8] 35
- Configuration [1.9] 35
- 34 Entry Keypad Lock 38
- 35 Tamp as Burg 38
- 37 Unconf Usr Rst 38
- 38 Keypad PA On 38
- RESET 1.9V to 2.4V 39
- MID 5.6 to 6.4V 39
- HIGH 9.0 to 10.1V 39
- Relearn Hardware [1.C] 40
- StarburstLCD 42
- Change Passcode [2.4] 43
- Chime Circuits [2.5] 43
- Alter Shunt Group [2.6] 43
- Print System Log [2.7] 43
- Configure Part Sets [2.8] 44
- View System Log [2.9] 44
- Log Event Codes 45
- Reset User Code 1 [2.0] 46
- Start Call Back [2.A] 46
- LCD Only 47
- Modem Password 48
- Modem Site No 48
- Program Digicom 48
- Text Editing Keys 50
- Cursor Types 50
- Common Key Sequences 50
- TS690/TS690ID 53
- Setup New Users Flowchart 54
- Engineers Menu 1 55
- Engineers Menu 2 56
- Output Types 56
- Quick Reference User Menus 57
- User Menu 1 57
- User Menu 2 57
- 496804 Issue 1 60
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Cooper TS690
(432 strony)
(110 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji